Get A Free Quote

 

What're your beliefs about How to Install a Bathtub Yourself?

Mounting a bath tub isn't precisely rocket science, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably challenging job. If the old tub is readily obtainable, the task can move quickly; if you need to open up a wall to get rid of the old bathtub and also place the new bath tub, the task is much harder. In either case, the project is within a home handyman's skills, although you will need an assistant to move out the old tub and set in the new one. Make certain you have actually qualified on your own for the task as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you begin. Chances are you may require an expert plumber to make tube links.
This article will assist you mount a new bath tub in your restroom if you have actually already bought a brand-new tub and do not need to transform the arrangement of your previous water system pipelines.
Your devices and material checklist ought to make up the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Adjustable Wrench


• Putty Blade


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old faucets with brand-new ones as a part of your installation, after that the first thing you must do is separate the supply of water. After doing so, turn on the faucets to drain any kind of water remaining in the system. The process of getting rid of the existing taps can be quite bothersome due to the restricted accessibility that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the remaining water that will certainly come from the pipes. Once the supply pipes have been gotten rid of, use the very same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before going on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.

 

 

Fitting New Touches

If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap and the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers are in place between the tap as well as the sink. Secure the faucet in position with the producer given backnut. As soon as the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with normal faucet adapters. The previous kind must be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.

 

 

Setting up the Bath tub

Using both wood boards under its feet, place the bathtub in the required placement. The wooden boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four tiny factors.
The following goal is to make certain that the tub is leveled all round. This can be accomplished by checking the level and adjusting the feet on the bathtub till the level reads degree.
To mount faucets, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other tap.
Turn on the water system and also inspect all joints and also brand-new pipework for leaks and also tighten them if necessary. Fill the tub and additionally check the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the producer's user's manual. Tiling and sealing around the tub ought to wait up until the bathtub has been used at least when as this will settle it right into its last placement.

 

 

Getting ready for the Setup

To start with, the sustaining structure provided with the bathroom needs to be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the taps unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use all of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom need to now be ready to be suited its last placement.

 

 

Tiling Around the Bathtub

In the area where the bathroom meets the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is important as the installation can move enough to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with moisture and also feasible leakages to the ceiling below.
You can select from a range of coloured sealers to assimilate your fixtures and also fittings. They are offered in tubes as well as cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked newspaper or soft rope. Remember to always load the tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealer can break fairly early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or water-proof sticky and cement.

 

How to Install a Freestanding Bathtub?

 

Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.

This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.

 

Slope

 

Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.

 

Placement

 

A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.

According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.

 

Clean the bathroom floor

 

After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.

 

Steps to Install a Freestanding Bathtub:

 

STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.

STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.

STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.

STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.

STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.

STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.

 

Tips to Maintain a Freestanding Bathtub:

 

• Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter.


 
• Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches.


 
• Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains.


 
• Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris.


 
• Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run.


 
• If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.

 

https://www.magnushomeproducts.com/blogs/inspired-living/how-to-install-a-freestanding-bathtub-a-diy-method-with-6-steps

 

I discovered that blog posting on How to Install a Bathtub when browsing on the internet. Liked our piece of writing? Please share it. Let another person check it out. Thank-you for going through it.

Maintain plumbing health; connect today.